Signal attenuation in networking means signal loss. It is the weakening or loss of signal strength during transmission. This is a natural consequence of signal transmission over long distances. The farther a signal wavelength travels, the smaller the amplitude becomes, therefore the weaker. This applies to both wired and wireless transmissions and applies to both analog and digital signals.
Other than distance, there are a few causes of signal attenuation:
- Long cabling – Over a long distance, transmitted signals slowly lose strength.
- Wire size – Thin wires experience more attenuation than thicker wires because they are more vulnerable to external interferences.
- Noise – Adjacent wires can cause electromagnetic interferences. The higher the noise, the higher the attenuation.
- Defective connectors and conductors – Poorly installed connectors and conductors lead to attenuation.
If the attenuation increases, then the quality of connectivity gets distorted or lost completely.
Proactively preventing signal attenuation
Technicians and operators alike must understand the signal attenuation of coax cabling and fiber-optic cabling they are installing. Calculating, measuring and testing the signal attenuation for the cabling at the point of installation helps prevent issues right away. The worst case is signal power loss due to attenuation becoming so low that the system loses connectivity to the network gateway. This in turn creates unhappy customers and bigger time and money issues for operators.
The amount of loss over coax cable depends on the type of cabling, the distance it is covering, and the frequency of the radio signal. While signal attenuation is common, it is important to get the measurement levels right at install. Signal attenuation is measured in decibels (dB) per unit distance.
The Hitron CGN-DP3 wireless DOCSIS 3.1 meter is a multi-tool that performs all of the major tests required by a field technician in order to accurately and efficiently troubleshoot issues inside and outside of the home. The CGN-DP3 should be used with the MyMeter App in order to get the maximum benefits from the device. Such as visual representation of diagnostic and measurement results and features like:
- Signal loss calculator
- Pressure tester
- Identifying signal noise
- Spectrum analysis
- Channel scan
- Ingress
- DOCSIS and more.
When paired with Hitron’s other offerings of full-home networking tools like the signal meter (CSN-01), it creates a very powerful suite of tools that provides cost savings, time savings, efficiencies, and standardized measurements with minimal training needed. Empower your technicians to troubleshoot the whole home with Hitron’s Whole Home Certification testing tools at a fraction of the cost of other solutions.
Learn More about Coax Network Testing Tools
How to Test and Pin-Point Coax Cable Signal Leakage with Pressure Testing
Cable signal leakage often happens when there are loose fittings, broken cables, or poorly connected fittings. When it happens, the source must be detected and contained. Detecting signal leakage at the cable plant is easier since signal levels are much higher than in...
Detect and Defeat Signal Leakage with One Simple Test
Cable signal leakage is an open invitation to cause disruption for customers and operators alike. For customers, signal leakage can cause negative experiences with online and voice services, poor picture quality and image freezing. This will undoubtedly lead to...
How Pressure Testing Can Reduce Your Operational Costs
Understanding the cause of cable signal leakage and how to prevent it can be critical for reducing operational costs. Mostly, this is because the FCC issue fines for interferences. The more severe the interference, like interfering aeronautical communication and LTE,...
What is a Spectrum Analyzer and How Can it Eliminate Signal Leakage?
A spectrum analyzer is a testing tool that measures and displays the amplitude versus frequency for input signals. The terms “spectrum analyzer” and “signal analyzer” are used almost interchangeably. But there are some slight differences. Spectrum analyzers are...
Avoid Signal Insertion Loss by Proactively Detecting It
Insertion loss can be defined as the attenuation of the signal as it passes through a passive device. The attenuation is caused by the passive device. The type of passive device determines the amount of attenuation it has on the signal. For example, as a signal...
Related Articles
How to Test and Pin-Point Coax Cable Signal Leakage with Pressure Testing
Pressure testing for cable signal leakage is necessary for outside plant testing at end users’ homes. It pin-points leaks with precision. Learn more.
Detect and Defeat Signal Leakage with One Simple Test
Hitron’s coax network testing tools help technicians seamlessly identify, isolate and control signal leakage issues with one simple test. Learn more.
How Pressure Testing Can Reduce Your Operational Costs
Pressure testing for cable signal leakage helps pinpoint the exact source right away. This can help save you money in a few ways. Learn more.
What is a Spectrum Analyzer and How Can it Eliminate Signal Leakage?
A spectrum analyzer is a helpful tool for technicians on the job site. It lets you monitor, test and troubleshoot before getting back to the plant or lab. Learn more.